Northlight systems isolated signal splitter PCB for DMX 512 offers full electrical isolation between the input and 3 outputs. Each output has it's own line driver and optical isolator.
In addition to signal isolation, power isolation is achieved with a UL listed split bobbin transformer and separate power supplies for the input and output sections.
Home Page DMX to 0-10 VDC converter DMX to Relay driver Convert 0-10VDC to DMX512 protocol. Isolated DMX splitter. DMX to Hobby servo DMX512 DC PWM boards Misc items on sale Application circuits for Encoder and Decoder Notes about DMX 512 protocol Trouble shooting guide. Warranty and disclaimer.
  • The Northlight Systems DMX splitter board is capable of isolating DMX512 signals.
  • Input is electrically isolated from the outputs. Devices are protected from failure at either end.
  • Outputs are isolated from each other.
  • Outputs are separately buffered.
  • Each output drives up to 32 receivers.
  • Selectable, onboard termination.
  • Uses 2500 volt optical couplers.
  • Easily isolates line voltage failures.
  • Data throughput higher than required.
  • Power and input signal indicators.
  • Not RDM compatable.
  • PC Board 3.92" X 4.70" Overall height 1.70"
  • Board accepts Neutrick PC mount, 5 pin XLR connectors.
    • Enclosure options
    The splitter board has 4 mounting holes.
    It will also fit in an extruded aluminum case or any case that has an inside dimension over 2" in height and 4.75" long X 3.95" wide.     		PacTec plastic enclosure

    The mounting holes in the board fit the mounting bosses in the PacTec CM5-200 plastic enclosure.
    Dimension 5.20”L X 5.10”W X 2.20”H.
    This is a good choice for use with panel mount XLR connectors.
    The LED’s can be bent to protrude through the end panel.

    		Extruded Aluminum
    The DMXiso3 board will also fit a Hammond extruded aluminum enclosure. These are available with plastic or aluminum end panels.
    Dimensions 4.72”L X 4.04”W X 2.09H.
    Hammond Part# 1455N1201Bk with aluminum end panels.
    Hammond part# 1455N1202Bk with plastic end panels.
    This is a good choice for use with PC mount XLR connectors. extruded aluminum enclosure
    3 Output isolated splitter.
  • 3.92" X 4.70".
  • 120 VAC input power
  • Non RDM
    Download the manual for the splitter in PDF format.
    		• Isolater splitter PCB

    DMXiso3
    $110.00 - Isolated splitter with solder pads.
    To purchase click on shipping and click icon.

    Input Qty -  

    		DMXiso3T
    $125.00 - Isolated splitter with screw terminals.
    To purchase click on shipping and click icon.

    Input Qty -  


    Other payment options include Company check, Electronic funds transfer, Western Union. Email for more information.
    SPECS:
    All specifications meet or exceed requirements for DMX512.
    ESD Protection to ±10kV on inputs and outputs protect against multiple ESD strikes of over ±10kV using the Human Body Model.
    Baud rate: 0 to 250 KB
    Input circuit: EIA-485 compatible receiver,
    Input signal: 0.2 volts minimum, 12 volts maximum
    Output circuit: Fast, 2500 volt optical isolators
    EIA-485 compatible drivers
    Connectors: solder pad or screw terminal.
    Power Isolation: Split bobbin, UL listed transformer
    Power input: 110 - 120 volts, 50/60 hertz, 1 amp. 220 volt available on request .
    PC mount fuse, not user servicable.
    Case Fits PAC plastic and extruded aluminum.
    Dimensions: 3 output,5 pin XLR: 4.70 X 3.90" wide
    Input terminator: Selected by toggle switch or jumper.
    Send  To info@NorthlightDMX.com.
    		Made in the USA.